Instrukcja Vivanco UR Z2 Pilot telewizyjny

Instrukcja

Universal TV- DVB Controller UR Z2

Before you start using the device, please first read through the safety information and this

o

perating instruction very carefully. Only then you can use all the functions safely and reli-

ably. Please maintain the operating instruction well and pass on to possible other owners.

I

ntended use

Universal remotes replace original remote controls etc. of consumer electronics devices. The device is

meant for sole use in private households and may not be used for commercial purposes. Any other use

i

s not deemed as intended use and may lead to material damages or even to personal injuries.

The manufacturer does not assume any liability for damages that have occurred due to unintended use.

Battery/rechargeable battery safety

Please read these instructions very carefully. Disregarding these instructions can cause

damages/injuries and possibly even an explosion of batteries/rechargeable batteries! Do not short-

circuit the contacts, for example by common storage with metallic objects. Do not expose batteries/

rechargeable batteries to long periods of direct sunlight or heat. Do not throw batteries/rechargeable

batteries into the fire. Do not open batteries/rechargeable batteries, they do not contain any parts that

need to be maintained. Only replace batteries/rechargeable batteries with the same type or with an

equivalent recommended by the manufacturer. Accumulators only: For charging accumulators, do only

use the charging functions integrated in the device or any other suitable chargers. Never charge batteries.

Inserting the batteries

Open the battery flap on the back of the remote control, press the tongue lightly downwards, then insert

2 alkaline AA batteries. Check that the polarity markings on the batteries and in the battery compartment

are correctly lined up (+=+), then close the flap carefully. – Always use undamaged batteries.

Adapting to appliances

In order to control e.g. your TV or DVB you must adapt or set the remote control to it. There are two

ways of doing so: direct control code entry or code search.

Direct control code entry using the enclosed list

Example: setting to control a Panasonic television set:

1. The attached list gives, for example, the Panasonic Code 0158. Please make sure you have

selected the correct list for television sets (TV).

2. To prepare code entry, press the SET button, keep it pressed and then press the required appliance

button, e.g. TV, additionally until the lamp (LED) lights constantly.

3. Then press the number buttons (e.g. 0158) in sequence.

4. Once the numbers have been entered the lamp goes out and the remote control is ready to control

your appliance.

5. Finally, test the control code setting by trying to control (in this example) your television set. If it does

not work at all or not correctly try a different code from the list or the code search (see below). You can

terminate the mode by pressing any device button.

Code search

If the brand of your appliance is not in the list or none of the codes given fits, we recommend a code

search.

Manual code search

1. Switch on the appliance to be controlled. Program is running.

2. To prepare code search, press the SET button, keep it pressed and then press the required

appliance button, e.g. TV, additionally until the lamp (LED) lights constantly.

3. Then point the remote control at the appliance to be controlled.

4. Briefly press the SET button once. The lamp (LED) blinks.

5. Press the ON/OFF (appliance on/off) button repeatedly for testing the next code, approx. every

1,5 seconds, until the appliance, e.g. your TV reacts by power off. - If your appliance has switched itself

off you must switch it back on again, e.g. on the appliance or with the original remote control, to continue

searching. - When your appliancereacts you can also try out other buttons without interrupting the

search. If some buttons do not work properly, simply continue searching with ON/OFF.

6. When your appliance reacts correctly, press the appliance button, e.g. TV, and end the search. The

lamp (LED) goes out. - The UR Z2 continues with the search at the point where you interrupted it. The

code last entered remains stored. The search stops after approx. 30 seconds of inactivity.

2

GB

BDA 34873-Rev-RZ_Layout 1 21.06.13 09:14 Seite 2

Ocena

Więcej o tej instrukcji

Rozumiemy, że miło jest mieć papierową instrukcję obsługi Vivanco UR Z2 Pilot telewizyjny. Zawsze możesz pobrać instrukcję z naszej strony internetowej i wydrukować ją samodzielnie. Jeśli chcesz otrzymać oryginalną instrukcję, zalecamy skontaktowanie się z Vivanco. Być może będą w stanie dostarczyć oryginalną instrukcję. Szukasz instrukcji swojego Vivanco UR Z2 Pilot telewizyjny w innym języku? Wybierz preferowany język na naszej stronie głównej i wyszukaj numer modelu, aby sprawdzić, czy jest on dostępny.

Dane techniczne

Wszystkie podręczniki dla Vivanco Pilot telewizyjny
Więcej podręczników Pilot telewizyjny

Często zadawane pytania dotyczące Vivanco UR Z2 Pilot telewizyjny

Nasz zespół wyszukuje przydatne informacje na temat produktu i udziela odpowiedzi na często zadawane pytania. Jeśli znajdziesz nieścisłości lub błędy w naszych odpowiedziach na pytania, poinformuj nas o tym przy pomocy naszego formularza kontaktowego.